Hyundai Santa Fe: Panorama Sunroof / Front Glass. Repair procedures
•
|
In order to remove the front glass, use the tools shown in the
following figure:
[Tooling Diagram]
① Square wire
② Insert-type wire grip
|
[Tooling Assembly Diagram]
•
|
Insert and affix square wire ① into the insert hole of the wire
grip ②.
|
|
1. |
Press panorama sunroof switch to fully open the movable glass.
|
2. |
Remove the side molding.
(Refer to Body Side Molding - "Roof Side Molding")
|
3. |
Pull the square wire (A) to the left and right, then apply a force in
the direction of the arrow to cut off the residual sealant.
• |
Longer wires require more power, so divide Section ①
and ② in half to cut off residual sealant.
|
|
• |
Make sure that you put on gloves to protect your hands
from potential injury.
|
• |
Be careful about potentially burning your hands due
to the heat generated from the wire in use.
|
• |
Be careful when working with wiring because it may be
cut.
|
|
• |
Be careful not to damage the body.
|
|
|
4. |
Remove the front glass (A) carefully without damaging it.
|
•
|
In order to mount the front glass, use the tools shown in the
following figure :
[Tooling Diagram]
① Sealant nozzle
② Adhesive sealant for car windows
③ Sealant gun
④ Primer
⑤ Primer application brush
|
|
1. |
Install the side molding.
(Refer to Body Side Molding - "Roof Side Molding")
|
2. |
Press panorama sunroof switch to fully close the movable glass.
|
3. |
Use a blade to cut off residual sealant (A) around the front glass attachment
area.
• |
When cutting off the residual sealant around the body
panel, make sure to leave about 2mm of sealant from
the adhesive surface.
|
|
• |
Make sure that the body paint surface is not damaged
at all.
|
• |
If it is damaged, apply paint or rust inhibitor for
maintenance.
|
|
|
4. |
Use alcohol or an air gun to clean up the edges of the panorama sunroof
frame and front glass.
|
5. |
Use a primer application brush to apply primer around the panorama sunroof
frame (A) and front glass.
|
6. |
Use a sealant gun to apply sealant (B) around the panorama sunroof frame
(A) after applying the primer
• |
When using a sealant gun to apply the sealant, make
sure that the sealant is not cracked to prevent water
leaks.
|
|
|
7. |
Install the front glass (A) loosely on the panorama sunroof frame.
|
8. |
Check step and gap before front glass (A) is fully mounted.
|
9. |
Apply tape to around the front glass to prevent the glass from coming
off.
• |
If sealant is excessively applied, it may ooze out of
the body. Use alcohol or a cleaning agent to wipe off
the residual sealant.
|
|
• |
Mount front glass and set the car on a flat surface
at least for 4 hours.
|
• |
If you have to drive the car, be sure to SLOWLY drive
the car for at least 8 hours after mounting.
|
• |
Alert the driver to avoid driving the car aggressively
for 2-3 days, or avoid driving it on irregular road
surfaces.
|
|
|
Replacement
1.
Remove the roof trim.
2.
Remove the movable glass.
(Panorama sunroof - refer "Movable Glass")
3...
Removal
•
In order to remove rear glass, use tools as follows shown in
the picture...
Other information:
..
Hyundai Digital Key (Smartphone) Pairing
1. Turn the vehicle on with the Smart key and make sure to keep the smart key
inside the vehicle during digital key registration.
2. Register your Digital key from the vehicle user setting menu as follows.
* With Navigation screen :
From the infotainment screen menu, go to [Setup] - [Vehicle] - [Digital Key] - [Smart
Phone Key] then select the [Save] from submenu...
Categories
The front seat can be adjusted by using the control switches located on the outside
of the seat cushion. Before driving, adjust the seat to the proper position so that
you can easily control the steering wheel, foot pedals and controls on the instrument
panel.
WARNING
NEVER allow children in the vehicle unattended. The power seats are operable
when the vehicle is turned off.
read more