Hyundai Santa Fe: Power Door Mirrors / Power Door Mirror Assembly. Repair procedures

Hyundai Santa Fe (TM) 2019-2025 Service Manual / Body Electrical System / Power Door Mirrors / Power Door Mirror Assembly. Repair procedures

Inspection
1.
Disconnect the negative (-) battery terminal.
2.
Remove the door trim.
(Refer to Body - "Front Door Trim")
3.
Disconnect the power door mirror connector (A) from the harness.
4.
Apply battery voltage to each terminal as shown in the table and verify that the mirror operates properly.
[Actuator]

BCW Indicator

Control Unit

Mirror Heater

Turn Signal Lamp

Puddle Lamp

Folding Mirror
Removal
1.
Disconnect (-) battery terminal.
2.
Remove front door trim.
(Refer to Body - "Front Door Trim")
3.
Remove door mirror assembly.
(Refer to Body - "Outside View Mirror")
4.
Using a fastener remover (C), remove the mirror (A) as illustration below.

  
•
Protect mirror from removing tool with cloth (B) wrapped.
•
Be careful not to damage mirror and mirror housing during removing process.
•
Apply force around the center of mirror because to apply force the end of mirror will break it.
5.
Disconnect heat wire connectors (A) and then remove the mirror.
6.
Remove the scalp.
1)
Attach protection tape at the end of the screw driver.
2)
Insert screw driver in where you can see the back of scalp.

  
•
When inserting screw driver, avoid to touch internal wires in the mirror housing.
3)
Hold the mirror assembly with one hand and hold the screwdriver with the other hand and strike it vertically as shown illustration below.

  
•
It is the way that screw driver strikes inner side of scalp cover to remove.
•
Lift screw driver and door mirror assembly about 20cm height from floor then smash them vertically.
•
scalp is thrown and removed because screw driver push the back of scalp cover to remove.
•
After removing the scalp, make sure that the clip and hook on the back of the scalp are not damaged.
•
If clips and hooks are damaged, replace the scalp with a new one as noise may occur in driving.
7.
Remove front cover and LED side repeater lamp lock screw.
8.
Using a fastener remover, remove the LED side repeater lamp as illustration below.

  
•
Be careful not to damage the LED side repeater lamp fixing hook (A).
9.
Disconnect the connector (A) and then remove the LED side repeater lamp.
Installation
1.
Install the puddle lamp and LED side repeater lamp.
2.
Install the scalp.
  
•
Install the scalp in the vertical direction that the inner fixing hook is not damaged.
•
When scalp installing, install the folded area first and then the far area.
•
Pushing the around of scalp with both hands and then make sure that it is completely installed.
3.
Connect mirror heat wire connector and BSD connector then mount mirror.
4.
Install the door mirror assembly.
5.
Connect (-) battery terminal then check if door mirror lamp works normally.

    Power Door Mirror Actuator. Repair procedures

    Removal 1. Disconnect (-) battery terminal. 2. Using a fastener remover (C), remove the mirror (A) as illustration below...

    Power Windows

    ..

    Other information:

    Hyundai Santa Fe (TM) 2019-2025 Service Manual: Specifications


    Specifications Item Specification Type Electric Power Steering System Steering gear Type Rack & Pinion Rack stroke 152 ± 1 mm(5...

    Hyundai Santa Fe (TM) 2019-2025 Service Manual: Rear Seat Belt Retractor. Components and components location


    ..

    Categories

    Electric Power Steering (EPS) warning light. Charging system warning light

    Electric Power Steering (EPS) warning light

    This warning light illuminates:

    When you set the ignition switch or the Engine Start/Stop button to the ON position.
    - The electric power steering warning light illuminates for about 3 seconds and then goes off. Whenever there is a malfunction with the electric power steering.
    If this occurs, have the vehicle inspected by an authorized HYUNDAI dealer.

    read more


     
    Copyright © 2025 www.hsafe4.com