Hyundai Santa Fe: Drive Belt System / Drive Belt. Repair procedures

Hyundai Santa Fe (TM) 2019-2025 Service Manual / Engine Mechanical System / Drive Belt System / Drive Belt. Repair procedures

Removal
  
Be careful not to damage the parts located under the vehicle (floor under cover, fuel filter, fuel tank and canister) when raising the vehicle using the lift.
(Refer to General Information - "Lift and Support Points")
1.
Remove the front tire.
(Refer to Suspension System - "Wheel")
2.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - "Engine Room Under Cover")
3.
Remove the RH front wheel guard.
(Refer to Body (Interior and Exterior) - "Front Wheel Guard")
4.
For release the tension, turn the drive belt tensioner clockwise using a wrench then remove the drive belt (A).

5.
Remove the water pump belt.
(1)
Insert the SST (09252-C1000) between the water pump pulley and the water pump belt.
(2)
Remove the water pump belt(A) by turning the damper pulley clockwise.

Installation
1.
Install the water pump belt.
(1)
Insert the SST (09252-C1000) between the water pump pulley and the water pump belt.
(2)
Remove the water pump belt(A) by turning the damper pulley clockwise.

2.
For release the tension, turn the drive belt tensioner clockwise using a wrench then install the drive belt (A).

Inspection
1.
Visually check the belt for excessive wear, frayed cords etc.
If any defect has been found, replace the drive belt.
  
Cracks on the rib side of a belt are considered acceptable. If the belt has chunks missing from the ribs, it should be replaced.

    Drive Belt System

    ..

    Drive Belt Tensioner. Repair procedures

    Removal and Installation    • Be careful not to damage the parts located under the vehicle (floor under cover, fuel filter, fuel tank and canister) when raising the vehicle using the lift...

    Other information:

    Hyundai Santa Fe (TM) 2019-2025 Service Manual: Troubleshooting


    Trouble Symptom Charts Trouble Symptom 1 Trouble Symptom 2 Trouble symptom Probable cause Remedy The set vehicle speed varies greatly upward or downward "Surging" (repeated alternating acceleration and deceleration) occurs after setting Malfunction of the vehicle speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of ECM Check input and output signals at ECM Trouble Symptom 3 Trouble symptom Probable cause Remedy The CC system is not canceled when the brake pedal is depressed Damaged or disconnected wiring of the brake pedal switch Repair the harness or replace the brake pedal switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 4 Trouble symptom Probable cause Remedy The CC system is not canceled when the shift lever is moved to the "N" position (It is canceled, however, when the brake pedal is depressed) Damaged or disconnected wiring of inhibitor switch input circuit Repair the harness or repair or replace the inhibitor switch Improper adjustment of inhibitor switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 5 Trouble symptom Probable cause Remedy Cannot decelerate (coast) by using the "SET/–" switch Temporary damaged or disconnected wiring of "SET/–" switch input circuit Repair the harness or replace the "SET/–" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 6 Trouble symptom Probable cause Remedy Cannot accelerate or resume speed by using the "RES/+" switch Damaged or disconnected wiring, or short circuit, or "RES/+" switch input circuit Repair the harness or replace the "RES/+" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 7 Trouble symptom Probable cause Remedy CC system can be set while driving at a vehicle speed of less than 40km/h (25mph), or there is no automatic cancellation at that speed Malfunction of the vehicle-speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 8 Trouble symptom Probable cause Remedy The cruise main switch indicator lamp does not illuminate (But CC system is normal) Damaged or disconnected bulb of cruise main switch indicator lamp Repair the harness or replace the part...

    Hyundai Santa Fe (TM) 2019-2025 Service Manual: Emergency Signal System. Description and operation


    Description Introduction of quick brake warning system (ESS) In case of quick brake by driver, the brake lamp or turn signal is blinked to warn against the vehicle at rear. 1. Basic function (Blinking the brake lamp/emergency lamp) – Operation condition : In case of quick brake or operation of ABS above in a certain speed – Releasing condition : In case of stopping the quick brake or releasing the ABS operation 2...

    Categories

    Electric Power Steering (EPS) warning light. Charging system warning light

    Electric Power Steering (EPS) warning light

    This warning light illuminates:

    When you set the ignition switch or the Engine Start/Stop button to the ON position.
    - The electric power steering warning light illuminates for about 3 seconds and then goes off. Whenever there is a malfunction with the electric power steering.
    If this occurs, have the vehicle inspected by an authorized HYUNDAI dealer.

    read more


     
    Copyright © 2025 www.hsafe4.com