Hyundai Santa Fe: IMS (Integrated Memory) / Description and operation

Hyundai Santa Fe (TM) 2019-2024 Service Manual / Body Electrical System / IMS (Integrated Memory) / Description and operation

Description
The optimal seat position set by the driver is memorized into the power seat unit by using IMS switch. In case of the position change, the seat can restore its preset position by IMS switch.
It has safety functions of restoring process prohibition during driving and of emergency stop of the linked motion.
The main functions are as follows.
1.
Manual operation : Motor control with the seat manual switch.
(1)
The position of the seat is changed by operating the motor when the signal is input with manual switch for the seat (Slide, recline, front tilt, rear height adjusting cushion extension)
2.
Memory function : Available for memorizing/reproducing the data for two persons with IMS switch.
(1)
The memorized motion for the optimal seat position set by the driver based on the CAN data with 『DDM → IMS module』with IMS switch.
(2)
Reproduction by the CAN data received from DDM during IMS switch controlling.
3.
Motion linked to getting on/off
(1)
This function links motion depending on the state of ON/OFF the engine.
(2)
Use of IMS CAN data communcation.
(3)
Condition for operating getting on : When the electric power is in ACC.
Operation
Reproducing Motion
1.
If the reproduction CAN data is received from DDM, the buzzer is issued one time and the seat is automatically moved to the memorized position.
2.
The CAN data not memorized does not perform reproduction function.
3.
If CAN data is newly received during previous data reproduction, the final data takes precedence.
4.
If the reproduction CAN data is received by pressing button 1 or 2 during reproduction, the seat stops the reproduction process.
5.
If the memorized CAN data is received by pressing SET button during reproduction, the seat stops the reproduction process.
  
Press the SET button once more to store the position of stop.
6.
Automatically stop when remart switch is OFF during reproduction.
7.
Do not operate the motor when the difference between the memorized position for reproduction and current position is less than 4 pulses.
Conditions for Prohibiting the Reproduction
In case any of the following conditions is met, the reproduction is prohibited and the controlling stops during reproduction.
1.
IGN2 OFF (Excluding within 30 seconds after door opening or closing.)
2.
Higher than 3km/h of vehicle speed
3.
When the switch is controlled manually
4.
Operation time chart

Decision on the Operation Priority
1.
For automatic control, the motor operation shall be delayed by 100±10m sec to prevent the overlapping of inrush circuit and in this case the priority shall be given as follows.
Slide > Backrest adjustment >Front height adjustment >Rear height adjustment > Cushion extension adjustment
Operation time chart

Operation Linked with Getting On/ Getting Off
1.
Returning motion to backwards during getting off and to forwards during getting on (applied only to slide).
2.
It is available when the automatic SET message transmitted from the driver seat power window switch (DDM) is ON.
3.
Operation starts when the engine is off and driver seat door is opened.
4.
Moving to the targeted position of ACC ON.
5.
Conditions for prohibiting operation.
Vehicle speed is 3km/h or more.
Power seat manual control switch is operated.
Reproduction command is received while getting on the vehicle.
Driver settings menu (USM) is OFF.

    IMS (Integrated Memory)

    ..

    Components and components location

    ..

    Other information:

    Hyundai Santa Fe (TM) 2019-2024 Service Manual: Troubleshooting


    Trouble Symptom Charts Trouble Symptom 1 Trouble Symptom 2 Trouble symptom Probable cause Remedy The set vehicle speed varies greatly upward or downward "Surging" (repeated alternating acceleration and deceleration) occurs after setting Malfunction of the vehicle speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of ECM Check input and output signals at ECM Trouble Symptom 3 Trouble symptom Probable cause Remedy The CC system is not canceled when the brake pedal is depressed Damaged or disconnected wiring of the brake pedal switch Repair the harness or replace the brake pedal switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 4 Trouble symptom Probable cause Remedy The CC system is not canceled when the shift lever is moved to the "N" position (It is canceled, however, when the brake pedal is depressed) Damaged or disconnected wiring of inhibitor switch input circuit Repair the harness or repair or replace the inhibitor switch Improper adjustment of inhibitor switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 5 Trouble symptom Probable cause Remedy Cannot decelerate (coast) by using the "SET/–" switch Temporary damaged or disconnected wiring of "SET/–" switch input circuit Repair the harness or replace the "SET/–" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 6 Trouble symptom Probable cause Remedy Cannot accelerate or resume speed by using the "RES/+" switch Damaged or disconnected wiring, or short circuit, or "RES/+" switch input circuit Repair the harness or replace the "RES/+" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 7 Trouble symptom Probable cause Remedy CC system can be set while driving at a vehicle speed of less than 40km/h (25mph), or there is no automatic cancellation at that speed Malfunction of the vehicle-speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 8 Trouble symptom Probable cause Remedy The cruise main switch indicator lamp does not illuminate (But CC system is normal) Damaged or disconnected bulb of cruise main switch indicator lamp Repair the harness or replace the part...

    Hyundai Santa Fe (TM) 2019-2024 Service Manual: Components and components location


    ..

    Categories

    Vehicle Identification Number (VIN). Vehicle certification label. Tire specification and pressure label

    Vehicle Identification Number (VIN)

    The vehicle identification number (VIN) is the number used in registering your vehicle and in all legal matters pertaining to its ownership, etc.

    The number is punched on the floor under the passenger seat. To check the number, open the cover.

    read more


     
    Copyright © 2024 www.hsafe4.com