Hyundai Santa Fe: Surround View Monitor (SVM) / Troubleshooting
| 1) |
After replacing controller, always check that the system operates
properly.
|
| 2) |
If the failure persists after replacing the controller, do not
replace the controller.
|
|
|
1. |
Inspection by DTC Code
Symptom
|
Probable Cause
|
Remedy
|
1. Single DTC code appearance
|
Loose connector relevant to a certain DTC code
|
1) Check connection status and reconnect the connector.
|
Tolerance compensation not completed
|
1) DTC code appearance (B103000)
2) Perform tolerance compensation.
|
Disconnected wiring
|
1) Inspect for conductivity of relevant area of DTC and wiring.
- DTC code generated (B16B700/B16B800/B16B900/B16BA00/C161600/B162C00)
|
Faulty wiring connector
|
1) Check for bent or damaged wiring connector pin.
2) DTC code generated (B16B700/B16B800/B16B900/B16BA00
|
Faulty controller connector
|
1) Check for bent or damaged controller connector pin.
2) DTC code generated (B16B700/B16B800/B16B900/B16BA00)
|
Faulty controller single unit or camera
|
1) Check basic operation and DTC on Diagnostic tool.
2) DTC code generated (B16B700/B16B800/B16B900/B16BA00)
|
2. Multiple DTC codes appearance
|
Loose SVM main connector
|
1) Check connection status and reconnect the connector.
|
Disconnected wiring
|
1) Camera power
- In case of 6V or below, inspect relevant wiring.
2) ACC/IGN power
- In case of 7.5V or below, inspect relevant wiring.
3) Parking/view button
- In case of 1.75V or higher with the switch ON, inspect relevant
wiring.
|
Faulty wiring connector
|
1) Check for bent wiring connector pin or interference in neighboring
parts.
2) DTC code generated (B16B700/B16B800/B16B900/B16BA00)
|
Faulty controller connector
|
1) Check for bent controller connector or interference in neighboring
parts.
2) DTC code generated (B16B700/B16B800/B16B900/B16BA00)
|
Faulty controller single unit
|
1) If failure recurs after the items above are confirmed normal,
replace SVM.
|
|
|
2. |
Inspection for Defect in SVM Performance (Image Output)
Symptom
|
Probable Cause
|
Remedy
|
1. No image output :
Black screen, Blue screen, Green screen
|
Loose controller or SVM main connector
|
1) Check connection status and reconnect the connector.
|
Disconnected controller or SVM wiring
|
1) Inspect for conductivity of ACC / IGN / V-OUT / M-CAN terminal
wiring
|
Faulty IPM (SJB)
|
1) Check power of ACC / IGN terminals : In case of 7.5V or below,
inspect IPM (SJB)
|
Faulty controller or SVM
|
1) If failure recurs after the items above are confirmed normal,
replace controller or SVM camera.
|
2. Abnormal image output :Noise on screen / lines / cracked display
/ unable to change display
|
Loose main connector
|
1) Check connection status and reconnect the connector.
|
Disconnected or short-circuited wiring
|
1) Inspect the wiring relevant to DTC appearance.
|
Faulty tolerance compensation
|
1) If the SVM image display is cracked even though the camera display
is normal, execute tolerance compensation again.
|
Faulty camera
|
1) If both camera display and SVM image display are cracked, inspect
the camera.
|
Faulty IPM (SJB)
|
1) In case of DTC code (C161600) appearance, inspect IPM (SJB).
|
Faulty console switch
|
1) Inspect parking/view button.
- In case of 1.75V or higher with the switch ON, replace the switch.
|
Faulty controller or SVM camera
|
1) If failure recurs after the items above are confirmed normal,
replace controller or SVM camera.
|
|
|
3. |
Inspection for Faulty PAS Warning Display & Parking Guideline
Symptom
|
Probable Cause
|
Remedy
|
1. Faulty PAS warning display & faulty parking guideline
|
H/UNIT option information not configured
|
1) Check and modify AVN option configuration status.
|
Loose main connector
|
1) Check connection status and reconnect the connector.
|
Faulty IPM (SJB)
|
1) Check that Parking Assist System (PAS) and Steering wheel Angle
Sensor (SAS) are normal.
2) Inspect IPM (SJB).
|
Faulty controller or SVM
|
1) If failure recurs after the items above are confirmed normal,
replace controller or SVM.
|
|
Inspection
Tolerance Compensation
Tolerance compensation compensates for the error margins of surround view video
that occur due to the installation tolerance when the four cameras that comprise
the SVM system are installed...
Other information:
Removal
•
Be careful not to damage the parts located under the vehicle
(floor under cover, fuel filter, fuel tank and canister) when
raising the vehicle using the lift...
Jump starting can be dangerous if done incorrectly. Follow the jump starting
procedure in this section to avoid serious injury or damage to your vehicle. If
in doubt about how to properly jump start your vehicle, we strongly recommend that
you have a service technician or towing service do it for you...
Categories
The armrest is located in the center of the rear seat. Pull the armrest down
from the seatback to use it.
read more
Repair procedures