Hyundai Santa Fe: Rear Seat / Rear Seat Back Cover. Repair procedures

Hyundai Santa Fe (TM) 2019-2024 Service Manual / Body (Interior and Exterior) / Rear Seat / Rear Seat Back Cover. Repair procedures

Replacement
[Second row seat assembly]
(LH)
  
Put on gloves to protect your hands.
  
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
Take care not to bend or scratch the trim and panels.
1.
Remove the second row seat assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Remove the rear seat lower protector (A).

3.
Loosen the mounting screw and remove the rear back hinge cover (A).

4.
Loosen the mounting bolt and remove the rear back armrest (A).

5.
Press the lock pin (A) and remove the rear back armrest pad (B).

6.
Press the lock pin and remove the rear seat headrest (A).

7.
Loosen the mounting bolts and nuts , remove the rear back hinge bracket (A).

8.
Loosen the mounting screws and remove the rear back armrest panel (A).

9.
Using a screwdriver or remover and remove the rear seat shield outer cover (A).

10.
Using a screwdriver or remover and remove the rear center seat belt cover (A).

11.
Loosen the rear center seat belt bolt (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

12.
Using a remover and remove the child anchor cover (A).

13.
Remove the rear seat lower protector (A).

14.
Press the lock pin and separate the seat heater connector (A).

15.
Press the hooks and remove the headrest guide (A).

16.
Remove the rear seat back cover assembly (A) from the rear seat frame.

17.
After removing the Velcro tape (A) and tie-down clips (B) inside the rear seat back cover, remove the rear seat back cover (C).

18.
To install, reverse removal procedure.
  
Replace any damaged clips.
(RH)
  
Put on gloves to protect your hands.
  
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
Take care not to bend or scratch the trim and panels.
1.
Remove the second row seat assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Push the lock pin (B), remove the rear seat headrest (A).

3.
Remove the rear seat lower protector (A).

4.
Loosen the mounting screw and remove the rear seat shield inner cover (A).

5.
Press the lock pin and separate the connector (A).

6.
Using a screwdriver or remover and remove the rear seat shield outer cover (A).

7.
Using a remover and remove the child anchor cover (A).

8.
Remove the rear seat back lower protector (A).

9.
Press the lock pin and separate the heater connector (A).

10.
Using a screwdriver or remover and remove the rear seat back cover (A).

11.
Press the hooks and remove the headrest guide (A).

12.
Using a remover and remove the rear seat back folding swich (A).

13.
Press the lock pin and separate the rear seat back folding swich connector (A).

14.
Remove the rear seat back cover assembly (A) from the rear seat frame.

15.
After removing the Velcro tape (A) and tie-down clips (B) inside the rear seat back cover, remove the rear seat back cover (C).

16.
Install in the reverse order of removal.
  
Replace any damaged clips.
[Third row seat assembly]
  
Put on gloves to protect your hands.
  
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
Take care not to bend or scratch the trim and panels.
1.
Remove the third row seat assembly.
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Press the lock pin and remove the headrest (A).

3.
Loosen the mounting screw and remove the rear seat outer cover (A).

4.
Loosen the mounting screw and remove the rear seat inner cover (A).

5.
Remove the rear seat strap cover (A).

6.
Open the rear seat back cover side zipper(A).
[LH]

[RH]

7.
Remove the seat back cover lower protector (A).

8.
Press the hooks and remove the headrest guide (A).

9.
Remove the rear seat back cover assembly (A) from the rear seat frame.

10.
After removing the Velcro tape (A) and tie-down clips (B) inside the rear seat back cover, remove the rear seat back cover (C).

11.
Install in the reverse order of removal.
  
Replace any damaged clips.

    Rear Seat Back Cover. Components and components location

    Component Location [Second row seat assembly] 1. Rear seat back cover [LH] 2. Rear seat back cover [RH] [Third row seat assembly] 1...

    Rear Seat Cushion Cover. Components and components location

    Component Location [Second row seat assembly] 1. Rear seat cushion cover [LH] 2. Rear seat cushion cover [RH] [Third row seat assembly] 1...

    Other information:

    Hyundai Santa Fe (TM) 2019-2024 Owner's Manual: System operation


    Ventilation 1. Set the mode to the position. 2. Set the air intake control to the outside (fresh) air position. 3. Set the temperature control to the desired position. 4. Set the fan speed control to the desired speed. Heating 1. Set the mode to the position...

    Hyundai Santa Fe (TM) 2019-2024 Service Manual: Rain Sensor. Repair procedures


    Removal    • Do not damage or touch the silicone (coupling medium). • Be careful so that the silicon is not contaminated by foreign substances, dust, etc...

    Categories

    Air bag collision sensors

    WARNING

    To reduce the risk of an air bag deploying unexpectedly and causing serious injury or death:

    Do not hit or allow any objects to impact the locations where air bags or sensors are installed. Do not perform maintenance on or around the air bag sensors. If the location or angle of the sensors is altered, the air bags may deploy when they should not or may not deploy when they should. Installing bumper guards with nongenuine Hyundai or non-equivalent parts may adversely affect the collision and airbag deployment performance. Press the Engine Start/Stop button to the OFF or ACC position and wait for 3 minutes when the vehicle is being towed to prevent inadvertent air bag deployment. Have all air bag repairs performed by an authorized HYUNDAI dealer.

    read more


     
    Copyright © 2024 www.hsafe4.com