Hyundai Santa Fe: Front Suspension System / Front Lower Arm. Repair procedures
1. |
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
|
2. |
Remove the front wheel and tire (A) from the front hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
|
• |
Be careful not to damage the hub bolts when removing
the front wheel and tire (A).
|
|
|
3. |
Remove the split pin and nut (A).
Tightening torque :
98.0 - 117.6 N.m (10.0 - 12.0 kgf.m, 72.3 - 86.7 lb-ft)
|
|
4. |
Remove the lower arm from the knuckle by using the SST (09568-4R100).
(1) |
Install the support bolt (A) from lower arm bolt hole.
|
(2) |
Install the support body (B) from front axle.
|
(3) |
Tighten the bolt (C).
|
|
5. |
Remove the lower arm (A) from the sub frame after loosening the mounting
bolts.
Tightening torque :
156.9 - 176.5 N.m (16.0 - 18.0 kgf.m, 115.7 - 130.2 lb-ft)
|
|
1. |
Check the bushing for wear and deterioration.
|
2. |
Check the lower arm for bending or breakage.
|
3. |
Check the lower arm for deformation.
|
4. |
Check the all bolts and nuts.
|
1. |
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
|
2. |
Remove the front wheel and tire (A) from the front hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
|
• |
Be careful not to damage the hub bolts when removing
the front wheel and tire (A).
|
|
|
3. |
Remove the split pin and nut (A).
Tightening torque :
98.0 - 117.6 N.m (10.0 - 12.0 kgf.m, 72.3 - 86.7 lb-ft)
|
|
4. |
Remove the lower arm from the knuckle by using the SST (09568-4R100).
(1) |
Install the support bolt (A) from lower arm bolt hole.
|
(2) |
Install the support body (B) from front axle.
|
(3) |
Tighten the bolt (C).
|
|
5. |
Remove the ball joint assembly after loosening the bolt (A) and nut
(B).
Tightening torque:
107.9 - 127.5N.m (11.0 - 13.0kgf.m, 79.6 - 94.0lb-ft)
|
|
Removal
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2...
Removal
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2...
Other information:
..
Blind-Spot Collision-Avoidance Assist is designed to help detect and monitor
approaching vehicles in the driver’s blind spot area and warn the driver of a possible
collision with a warning message and audible warning.
In addition, if there is a risk of collision when changing lanes or driving forward
out of a parking space, the system will help avoid a collision by applying the brake...
Categories
Electric Power Steering (EPS) warning light
This warning light illuminates:
When you set the ignition switch or the Engine Start/Stop button to
the ON position.
- The electric power steering warning light illuminates for about 3 seconds
and then goes off.
Whenever there is a malfunction with the electric power steering.
If this occurs, have the vehicle inspected by an authorized HYUNDAI dealer.
read more