Hyundai Santa Fe (TM): Engine And Transaxle Assembly / Engine Mounting. Repair procedures

Hyundai Santa Fe (TM) 2019-2023 Service and Repair Manual / Engine Mechanical System / Engine And Transaxle Assembly / Engine Mounting. Repair procedures

Removal and Installation
  
•
Be careful not to damage the parts located under the vehicle (floor under cover, fuel filter, fuel tank and canister) when raising the vehicle using the lift.
(Refer to General Information - "Lift and Support Points")
Roll Road Bracket
1.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - "Engine Room Under Cover")
2.
Remove the roll rod bracket (A).
Tightening torque
Bolt (B) :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
Bolts (C) :
49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb-ft)

3.
Remove the roll rod mounting support bracket (A).
Tightening torque :
49.0 - 68.6 N.m (5.0 - 7.0 kgf.m, 36.2 - 50.6 lb-ft)

Engine Mounting Bracket
1.
Remove the engine room under cover.
(Refer to Engine and transaxle Assembly - "Engine Room Under Cover")
2.
Remove the engine cover.
(Refer to Engine and transaxle Assembly - "Engine Cover")
3.
Install the jack to the edge of oil pan to support the engine.
  
•
Insert the rubber block between jack and oil pan.
4.
Remove the engine mounting support bracket (A).
Tightening torque
Bolt, Nuts (C) : 63.7 - 83.4 N.m (6.5 - 8.5 kgf.m, 47.0 - 61.5lb-ft)

5.
Remove the reservoir tank.
(Refer to Cooling System - "Reservoir Tank")
6.
Remove the engine mounting bracket (A).
Tightening torque :
63.7 - 83.4 N.m (6.5 - 8.5 kgf.m, 47.0 - 61.5 lb-ft)

7.
Install in the reverse order of removal.
Transaxle Mounting Bracket
1.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - "Engine Room Under Cover")
2.
Remove the air duct.
(Refer to Intake and Exhaust System - "Air Cleaner")
3.
Remove the air cleaner assembly.
(Refer to Intake and Exhaust System - "Air Cleaner")
4.
Remove the battery and tray.
(Refer to Engine Electrical System - "Battery")
5.
Install the jack to the edge of transaxle.
  
•
Insert the rubber block between jack and transaxle.
6.
Remove the transaxle mounting bolts (A).
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)

7.
Remove the transaxle mounting bracket (A).
Tightening torque :
63.7 - 83.4 N.m (6.5 - 8.5 kgf.m, 47.0 - 61.5 lb-ft)

8.
Install in the reverse order of removal.

    Components 1. Transaxle mounting bracket 2. Roll rod bracket 3. Engine mounting bracket 4. Engine mounting support bracket

    Removal    • Be careful not to damage the parts located under the vehicle (floor under cover, fuel filter, fuel tank and canister) when raising the vehicle using the lift.

    Other information:

    Hyundai Santa Fe (TM) 2019-2023 Service and Repair Manual: Evaporator Core. Repair procedures

    Replacement 1. Disconnect the negative (-) battery terminal. 2. Remove the heater and blower assembly. (Refer to Heater - "Heater Unit") 3. Remove the heater core.

    Hyundai Santa Fe (TM) 2019-2023 Service and Repair Manual: Rear Heater Unit. Components and components location

    Component Location 1. Rear Heater & A/C Unit Components 1. Rear heater & blower unit assembly 2. Blower motor assembly 3. Rear power mosfet 4. Duct seal guide 5.

    Categories

     
    Copyright © 2025 www.hsafe4.com - 0.0161