Hyundai Santa Fe: Blower / Blower Unit. Repair procedures

Hyundai Santa Fe (TM) 2019-2024 Service Manual / Heating,Ventilation And Air Conditioning / Blower / Blower Unit. Repair procedures

Replacement
1.
Disconnect the negative (-) battery terminal.
2.
Recover the refrigerant with a recovery/recycling/charging station.
3.
When the engine is cool, drain the engine coolant from the radiator.
(Refer to Engine Mechanical System - "Coolant")
4.
Remove the cowl top cover.
(Refer to Body - "Cowl Top Cover")
5.
Loosen the mounting bolts and separate the expension valve (A) from the evaporator core.
Tightening torque :
8.8 - 13.7 N.m (0.9 - 1.4 kgf.m , 6.5 - 10.1 lb-ft)

6.
Separate the heater hose (A).

7.
Loosen the cowl cross bar assembly mounting bolts.

8.
Remove the front seat assembly.
(Refer to Body - "Front Seat Assembly")
9.
Remove the floor console assembly.
(Refer to Body - "Floor Console Assembly")
10.
Remove the front pillar trim.
(Refer to Body - "Front Pillar Trim")
11.
Remove the cowl side trim.
(Refer to Body - "Cowl Side Trim")
12.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Lower Panel")
13.
Remove the steering column shroud panel.
(Refer to Body - "Steering Column Shroud Panel")
14.
Remove the steering wheel.
(Refer to Steering System - "Steering Wheel")
15.
Remove the multifunction switch.
(Refer to Body Electrical System - "Multifunction Switch")
16.
Lower the steering column after loosening the mounting bolts.
(Refer to Steering System - "Steering Column and Shaft")
17.
Remove the front door scuff trim.
(Refer to Body - "Door Scuff Trim")
18.
Loosen the mounting bolt and nut, remove the accelerator pedal module (A).

19.
Press the lock pin, separate the accelerator pedal connector (A).

20.
Remove the rear air duct (A) and then separate the floor carpet (B) backwards.
21.
Loosen the mounting nuts and remove the rear heating duct (A).

22.
Disconnect the junction box connectors (A).

23.
Disconnect the multi box connectors (A).
[Driver]

[Passenger]

24.
Loosen the mounting clips (B) in the front pillar and Disconnect the connectors (A).
[Driver]

[Passenger]

25.
Remove the drain hose (A).

26.
Remove the lower mounting bolt of the blower unit.
Tightening torque :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m , 2.9 - 4.3 lb-ft)
[Driver]

[Passenger]

27.
After loosening the bolts and nuts remove the crash pad and heater & blower unit assembly (A) together.

28.
Disconnect the heater & blower unit connectors.
(1)
Press the lock pin, separate the evaporator temperature sensor connector (A).

(2)
Press the lock pin, separate the mode control actuator connector (A) and driver's temperature control actuator connector (B).

(3)
Press the lock pin, separate the intake actuator connector (A).

(4)
Press the lock pin, separate the power mosfet connector (A).

(5)
Press the lock pin, separate the PTC heater connector (A).

(6)
Press the lock pin, separate the blower motor connector (A).

(7)
Press the lock pin, separate the PM sensor connector (A).

(8)
Press the lock pin, separate the auto defogging actuator connector (A) and passenger's temperature actuator connector (B).

29.
Loosen the heater & blower unit mounting bolt (A).
Tightening torque :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m , 2.9 - 4.3 lb-ft)

30.
Loosen the mounting nuts and remove the heater & blower unit (A) from the crash pad.
Tightening torque :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m , 2.9 - 4.3 lb-ft)

31.
Loosen the mounting screw and separate the blower unit (A).
Tightening torque :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m , 2.9 - 4.3 lb-ft)

32.
Install in the reverse order of removal.

    Blower Unit. Components and components location

    Components Location 1. Blower unit assembly Components 1. Blower unit assembly 2...

    Blower Motor. Repair procedures

    Inspection 1. Connect the battery voltage and check the blower motor rotation. 2. If the blower motor does not operate well, substitute with a known-good blower motor and check for proper operation...

    Other information:

    Hyundai Santa Fe (TM) 2019-2024 Service Manual: Position Switch. Troubleshooting


    Fault Diagnosis ▶ Fault Diagnosis for Symptom Major Symptom Expected Cause Items to Check and Measures Shift lever inoperable Faulty shift cable tension Adjust shift cable tension (refer to "Automatic Transaxle System – Position Switch") Faulty shift cable assembly/connection Check manual control valve assembly and re-assemble if necessary...

    Hyundai Santa Fe (TM) 2019-2024 Service Manual: Rear Door Window Glass. Repair procedures


    Replacement 1. Remove the rear door trim. (Refer to Rear door - " Rear door trim") 2. Using a remover and separate the rear door belt outside weatherstrip (A)...

    Categories

    Engine oil pressure warning light. Low fuel level warning light

    Engine oil pressure warning light

    This warning light illuminates:

    When the engine oil pressure is low.

    If the engine oil pressure is low:

    1. Drive carefully to the nearest safe location and stop your vehicle.

    2. Turn the engine off and check the engine oil level (For more details, refer to “Engine Oil” section in chapter 9). If the level is low, add oil as required.

    read more


     
    Copyright © 2024 www.hsafe4.com