Hyundai Santa Fe: Hydraulic System / Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures

Hyundai Santa Fe (TM) 2019-2024 Service Manual / Automatic Transaxle System (SBC) / Hydraulic System / Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures

Inspection
  
Refer to the DTC manual for the check procedure.
Removal
  
Be careful not to damage the parts located under the vehicle (floor under cover, fuel filter, fuel tank and canister) when raising the vehicle using the lift.
(Refer to General Information - "Lift and Support Points")
When the solenoid valve Diagnostic Trouble Codes (DTC) is on, perform the following procedure to replace it.
Automatic transaxle is composed of delicate components. Be careful not to cause any damage on the component in the course of assembly and disassembly.
Maintain clean condition so that foreign substance does not get into the automatic transaxle.
Use a coated apron, latex gloves, and stainless tray to prevent foreign substance from getting into the transaxle.
Automatic transaxle fluid (ATF) can be reused. Collect it using a clean 10-liter beaker.
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the air duct and the air cleaner assembly.
(Refer to Engine Mechanical System - "Air Cleaner")
3.
Separate the air bleed hose (B) and then wiring bracket (A).

4.
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
5.
Remove the drain plug (A) and reinstall the drain plug after draining ATF totally.
Drain plug tightening torque :
33.3 - 43.1 N.m (3.4 - 4.4 kgf.m, 24.6 - 31.8 lb-ft)

  
Replace the gasket before reinstalling the drain plug.
6.
Loosen the mounting bolts (A) of the valve body cover.
Tightening torque :
11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb-ft)

  
Be careful when removing the valve body cover because the remaining ATF remains in the valve body cover.
  
Replace the gasket (A) before reinstalling the valve body cover.
After the installation, start the engine and then check if there are any leakages from the valve body cover.

7.
Loosen the bolts and then removing the main harness (A).
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb-ft)

8.
Loosen the bolts and then removing the support bracket (A).
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

9.
Remove the line pressure control solenoid valve (A).

Installation
1.
To install, reverse the removal procedure.
2.
Inject the automatic transaxle oil and inspect the oil level.
(Refer to Automatic Transaxle System - "Automatic Transaxle Fluid")
  
After ATF level check or exchange, be sure to remove residual ATF on transaxle case.
(Be especially sure to remove residual ATF between automatic transaxle case and valve body cover)
After installing the valve body cover, make sure to check the oil leakage at the connection area with the engine ON
3.
Clear the diagnostic trouble codes (DTC) using the diagnostic tool.
(Refer to Automatic Transaxle System - "Automatic Transaxle")
  
Even though disconnecting the battery negative terminal, the DTCs will not be cleared. So, be sure to clear the DTCs using the diagnostic tool.
4.
In order to prevent start delay and gear shift shock during acceleration and start, perform TCM learning after replacing the solenoid valve.
(Automatic Transaxle Control System - "Repair Procedures")

    Line Pressure Control Solenoid Valve (LINE_VFS). Specifications

    Specifications ▷ Control type : Normally high type Shape Items Specifications Control current [mA] 0 - 850 Supply pressure [kpa (kgf/cm², psi)] 539...

    35R Clutch Control Solenoid Valve (35R/C_VFS). Description and operation

    Description • 35R Clutch control solenoid valve(35R/C) is attached to the valve body. • This variable force solenoid valve directly controls the hydraulic pressure inside the 35R clutch...

    Other information:

    Hyundai Santa Fe (TM) 2019-2024 Owner's Manual: Four Wheel Drive (4WD) mode selection


    WARNING If 4WD warning light () stays on the instrument cluster, your vehicle may have a malfunction with the 4WD system. When the 4WD warning light () illuminates have the vehicle be checked by an authorized HYUNDAI dealer as soon as possible. CAUTION When driving on normal roads, deactivate the 4WD LOCK mode by pushing the 4WD LOCK button (4WD LOCK indicator light goes off)...

    Hyundai Santa Fe (TM) 2019-2024 Owner's Manual: Gasoline Particulate Filter (GPF)


    Gasoline Particulate Filter (GPF) system removes the soot in the exhaust gas. The GPF system automatically burns (or oxidizes) the accumulated soot in accordance with driving situations, unlike a disposable air filter. In other words, the accumulated soot is automatically purged out by the engine control system and by the high exhaustgas temperature at normal/ high driving speeds...

    Categories

    Electric Power Steering (EPS) warning light. Charging system warning light

    Electric Power Steering (EPS) warning light

    This warning light illuminates:

    When you set the ignition switch or the Engine Start/Stop button to the ON position.
    - The electric power steering warning light illuminates for about 3 seconds and then goes off. Whenever there is a malfunction with the electric power steering.
    If this occurs, have the vehicle inspected by an authorized HYUNDAI dealer.

    read more


     
    Copyright © 2024 www.hsafe4.com