Hyundai Santa Fe: Airbag Module / Side Airbag (SAB) Module. Repair procedures

Hyundai Santa Fe (TM) 2019-2024 Service Manual / Restraint / Airbag Module / Side Airbag (SAB) Module. Repair procedures

Removal
1.
Disconnect the battery negative cable and wait for at least 3 minutes before beginning work.
2.
Remove the front seat assembly.
(Refer to Body - "Front Seat Assembly")
3.
Remove the seat back cover.
(Refer to Body - "Front Seat Back Cover")
  
When the front side airbag has deployed after a collision, replace the seat back as an assembly.
4.
Loosen the SAB mounting nuts and remove the SAB module (A).

  
The removed airbag module should be stored in a clean and dry place with the cushion side up.
Installation
  
Be sure to install the harness wires so they will not pinch or interfere with other parts.
  
Do not open the lid of the side airbag cover.
Make sure that the airbag assembly cover is installed properly. Improper installation may prevent a proper deployment.
1.
Disconnect the battery negative cable and wait for at least three minutes.
2.
Place a side airbag on the side airbag frame and tighten the side airbag mounting bolts.
Tightening torque :
7.8 - 11.8 N.m (0.8 - 1.2 kgf.m, 5.7 - 8.7 lb-ft)
3.
Install a new seat back cover.
(Refer to Body - "Front Seat Back Cover")
4.
Install the front seat assembly, and then connect the side airbag harness connector.
5.
After installing the side airbag (SAB), confirm proper system operation:
Turn the ignition switch ON; the SRS indicator light should turn on for about six seconds and then go off.
6.
Install a front seat assembly.
(Refer to Body - "Front Seat Assembly")
7.
Recline and slide the front seat forward fully, make sure the harness wires are not pinched or interfered by other parts.
8.
Reconnect the battery negative cable.

    Side Airbag (SAB) Module. Components and components location

    ..

    Curtain Airbag (CAB) Module. Description and operation

    Description Curtain airbags are installed inside the headliner (LH and RH) and protect the driver and passenger from danger when a side crash occurs...

    Other information:

    Hyundai Santa Fe (TM) 2019-2024 Owner's Manual: Resetting the system


    Take the following procedures to reset integrated memory system, when it does not operate properly. Resetting integrated memory system 1. Stop the vehicle and open the driver’s door with the Engine Start/Stop button in the ON position and the vehicle shifted to P (Park)...

    Hyundai Santa Fe (TM) 2019-2024 Owner's Manual: Vehicle load limit


    Two labels on your driver’s door sill show how much weight your vehicle was designed to carry: the Tire and Loading Information Label and the Certification Label. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle’s weight ratings, from the vehicle’s specifications and the Certification Label: Base Curb Weight This is the weight of the vehicle including a full tank of fuel and all standard equipment...

    Categories

    Air bag collision sensors

    WARNING

    To reduce the risk of an air bag deploying unexpectedly and causing serious injury or death:

    Do not hit or allow any objects to impact the locations where air bags or sensors are installed. Do not perform maintenance on or around the air bag sensors. If the location or angle of the sensors is altered, the air bags may deploy when they should not or may not deploy when they should. Installing bumper guards with nongenuine Hyundai or non-equivalent parts may adversely affect the collision and airbag deployment performance. Press the Engine Start/Stop button to the OFF or ACC position and wait for 3 minutes when the vehicle is being towed to prevent inadvertent air bag deployment. Have all air bag repairs performed by an authorized HYUNDAI dealer.

    read more


     
    Copyright © 2024 www.hsafe4.com