Hyundai Santa Fe: Rear Seat / Rear Seat Cushion Cover. Repair procedures
[Second row seat assembly]
•
|
Put on gloves to protect your hands.
|
|
•
|
When prying with a flat-tip screwdriver, wrap it with protective
tape, and apply protective tape around the related parts, to
prevent damage.
|
•
|
Use a plastic panel removal tool to remove interior trim pieces
to protect from marring the surface.
|
•
|
Take care not to bend or scratch the trim and panels.
|
|
1. |
Remove the second row seat assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
2. |
Remove the protector (A) located in the bottom side of the rear seat
cushion.

|
3. |
After loosening the mounting screw, then remove the rear seat recliner
knob (A).

|
4. |
After loosening the mounting screw, then remove the rear seat recliner
cover (A).

|
5. |
Remove the protector (A) located in the side part of the rear seat cushion.

|
6. |
Remove the rear seat cushion cover (A) from the rear seat cushion frame.

|
7. |
After removing the velcro tape (A) on the rear of seat cushion and remove
the rear seat cushion cover (B).

|
8. |
Install in the reverse order of removal.
• |
Replace any damaged clips.
|
|
|
•
|
Put on gloves to protect your hands.
|
|
•
|
When prying with a flat-tip screwdriver, wrap it with protective
tape, and apply protective tape around the related parts, to
prevent damage.
|
•
|
Use a plastic panel removal tool to remove interior trim pieces
to protect from marring the surface.
|
•
|
Take care not to bend or scratch the trim and panels.
|
|
1. |
Remove the second row seat assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
2. |
Remove the protector (A) located in the bottom side of the rear seat
cushion.

|
3. |
After loosening the mounting screw, then remove the rear seat slide
knob (A).

|
4. |
After loosening the mounting screw, then remove the rear seat slide
outer cover (A).

|
5. |
Remove the seat protector (A) from the rear seat cusion frame.
[Upper]

[Lower]

[LH]

[RH]

|
6. |
Remove the rear seat cushion cover (A) from the rear seat cushion frame.

|
7. |
After removing the velcro tape (A) on the rear of seat cushion and remove
the rear seat cushion cover (B).

|
8. |
Install in the reverse order of removal.
• |
Replace any damaged clips.
|
|
|
[Third row seat assembly]
•
|
Put on gloves to protect your hands.
|
|
•
|
When prying with a flat-tip screwdriver, wrap it with protective
tape, and apply protective tape around the related parts, to
prevent damage.
|
•
|
Use a plastic panel removal tool to remove interior trim pieces
to protect from marring the surface.
|
•
|
Take care not to bend or scratch the trim and panels.
|
|
1. |
Remove the third row seat assembly.
(Refer to Rear Seat - "Rear Seat Assembly")
|
2. |
Remove the rear seat rear protector (A).

|
3. |
Remove the rear seat cusion cover (A) from the rear seat cusion frame.

|
4. |
After removing the velcro tape (A) on the rear of seat cushion and remove
the rear seat cushion cover (B).

|
5. |
Install in the reverse order of removal.
• |
Replace any damaged clips.
|
|
|
Component Location
[Second row seat assembly]
1. Rear seat
cushion cover [LH]
2. Rear seat
cushion cover [RH]
[Third row seat assembly]
1...
Component Location
[Second row seat assembly]
(LH)
1. Rear seat
back frame assembly
2. Rear seat
cushion frame assembly
(RH)
1...
Other information:
Components Location
1. ECM (Engine
Control Module)
2. Manifold Absolute Pressure Sensor (MAPS)
3. Intake Air Temperature Sensor (IATS)
4. Engine Coolant Temperature Sensor (ECTS)
5. Throttle Position Sensor (TPS)
6...
..
Categories
Electric Power Steering (EPS) warning light
.png)
This warning light illuminates:
When you set the ignition switch or the Engine Start/Stop button to
the ON position.
- The electric power steering warning light illuminates for about 3 seconds
and then goes off.
Whenever there is a malfunction with the electric power steering.
If this occurs, have the vehicle inspected by an authorized HYUNDAI dealer.
read more